Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Port Richmond Homeowners
A missing cap or a cracked crown lets water straight into the top of your chimney, and water is what does the slow damage in Port Richmond’s older rowhouse stock: saturated brick, spalled mortar, a rusted damper, and eventually a flue that needs relining. Caps and crowns are the cheapest part of the system to fix and the most expensive to ignore. Our technicians have up to 12 years of experience and work with purpose-built caps from Gelco and Famco rather than improvised covers from the hardware aisle. We handle the full chimney system, from the firebox to the crown, so the person who inspects your flue is the same outfit that repairs the top of it. Fast dispatch runs 7am to 7pm, Sunday through Friday. Call (833) 754-6815.
What Our Chimney Cap & Crown Service Includes
Every one of these jobs starts with a look at the whole top of the chimney, not just the part that’s obviously broken. A loose cap usually means a failing crown underneath it, and a crown that’s cracked at the edge usually means water has been tracking into the flue for a while. We quote the work that actually needs doing and tell you plainly when a repair can safely wait.
Cap Installation
A chimney cap is the lid over the flue: a metal top on legs or a full shroud that keeps rain, snow, birds, squirrels and downdrafting wind out of the chimney. We install single-flue and full-shroud caps sized to your actual flue opening, with a stainless or galvanized mesh screen that keeps animals out without blocking exhaust. If your chimney has never had a cap, this is the first thing we’d recommend, because an open flue in Port Richmond takes on rain with every storm that rolls up the river.

Cap Replacement
Caps fail in predictable ways: rust-through on the top plate, a screen torn open by a raccoon, legs that have pulled loose from the flue tile in a freeze-thaw cycle. We pull the old cap, check the flue tile and crown underneath it, and fit a replacement from Gelco or Famco built for the flue size rather than a generic cover held down with masonry screws. You get a cap that’s engineered for the job and a clear answer on whether anything below it was damaged while the old one was failing.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the brick below. When it cracks, water gets behind the crown, freezes, and pushes the crack wider each winter until brick faces start to pop. We repair crowns by cutting out the failed section, bonding the new material to sound concrete, and rebuilding the overhang that throws water clear of the chimney walls. Small cracks get patched; a crown that’s crumbling across the whole top gets rebuilt.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a crown that’s sound but showing hairline cracks or surface wear. It’s the right call when the concrete is still structurally intact and you want to stop the freeze-thaw cycle before it opens the crown up. We coat only after the surface is cleaned and the small cracks are filled, so the membrane bonds to something solid. If the crown is already loose or broken through, coating is the wrong answer and we’ll tell you so.
Multi-Flue Cap
Port Richmond has plenty of chimneys serving more than one flue, and those need a single cap that covers the whole top rather than one lid per opening. A multi-flue cap spans the crown on a custom frame, protects every flue at once, and looks tidier than a cluster of individual caps. We measure each flue opening and the overall crown dimensions so the cap sits level and the screens line up over the right flues.
Custom Cap
Oversized crowns, offset flues, unusual tile arrangements and chimneys with a decorative shroud all need a cap fabricated to fit. We take the measurements on site and have a custom cap built to the flue layout, then set it so it sheds water and holds up to wind without the wobble you get from a one-size cover. This is also the option when a homeowner wants a particular look at the top of the chimney that still performs as a real cap.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Gelco caps, and we know where they wear: the top plate and the screen crimp are what fail first on an older unit, while the frame itself usually has plenty of life left. That knowledge matters when we’re replacing one, because we can tell you whether a new cap is genuinely needed or a repair will do. We also install Famco caps, which hold up well on the multi-flue chimneys common on the larger rowhouses around Port Richmond.
Olympia Chimney and HeatShield come into the conversation when the cap and crown work reveals a flue problem underneath. HeatShield is a liner restoration system that reschedules a deteriorating flue without tearing the chimney apart, and we apply it where the flue is sound enough to take it. Olympia Chimney products cover the liner and venting side of the job when a full liner replacement is the honest answer. Whether you have Gelco, Famco, Olympia Chimney, HeatShield or any other make on your chimney, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you’re finding dampness, rust stains or a musty smell in the firebox after a storm, the cap or crown is letting water in somewhere above. It’s usually a cheap fix at this stage and gets expensive once the damper and smoke chamber are wet.
- A visible crack in the crown. Hairline cracks in the concrete top are the first stage of freeze-thaw damage. Each winter the water in the crack expands and widens it, so a crown that’s cracked now is a crown that’s breaking up in a few seasons.
- Birds, squirrels or nesting material in the flue. An open or damaged flue is an easy way in for animals, and nests block the draft and create a fire risk. A screened cap closes the door permanently.
- Rust on the cap or a torn screen. Rust-through on the top plate and a screen pulled open by wildlife are the two most common cap failures we see. A cap in that condition is no longer keeping anything out.
- Crumbling mortar or loose brick at the chimney top. When the crown stops shedding water, the brick and mortar just below it start to go. That’s the point where the job moves from a crown repair toward masonry work, so it’s worth a look before it gets there.
Our Chimney Cap & Crown Process – Step by Step
- 1
We look at the whole top of the chimney. The inspection covers the cap, the crown, the flue tiles and the brick just below the crown. We’re checking how water is getting in and whether it’s already caused damage underneath, not just confirming that the cap is missing.
- 2
We show you what we found. Photos of the crown and flue from the top, so you can see the crack or the rust instead of taking our word for it. You get a written estimate that sets the final price, and nothing gets added afterward without your say-so.
- 3
We set up and protect the roof. A cap and crown job means working at the top of the chimney, so the area below gets protected before anything comes apart. Old caps, cracked crown sections and loose mortar come down in a controlled way.
- 4
We repair or install. Crown repair or coating goes on first where it’s needed, because the cap’s job is to protect the crown and the crown’s job is to protect the brick. Then the new cap is fitted to the flue and sealed at the joint so water can’t run back down the tile.
- 5
We check the draft and clean up. Before we leave we confirm the flue still draws properly with the new cap in place and that the screens are clear. You get the photos from the finished work and a plain answer on when the chimney should next be looked at.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Port Richmond?
Crown and cap work is priced per job by a written estimate, and the range depends mostly on what’s under the old cap when it comes off. A typical single-flue cap install in Port Richmond runs $250 – $650, while a multi-flue or custom cap for a larger rowhouse chimney runs $600 – $1,400 depending on the number of flues and the frame. Crown work is where the numbers spread: a crown coating over a sound crown runs around $400 – $800, a crown repair of a cracked or partly failed crown runs $600 – $1,200, and a full crown rebuild runs $1,200 – $2,500. If the flue underneath turns out to need a HeatShield restoration, that’s a separate line item in the estimate, and we’ll explain why it’s needed with the photo evidence in hand.
What moves the price is access (steep or high roofs take more setup), the number of flues, whether the old cap comes off cleanly, and how far the water damage has gone into the crown and brick. To avoid overpaying, get the crown and cap assessed together rather than in two visits, ask for the flue tile checked while the cap is off, and ask plainly whether the crown needs rebuilding or can be coated. Anything that can safely wait, we’ll say so. The free estimate covers the inspection, the photos and a written scope with the final price on it.
Chimney Cap & Crown Near Port Richmond – Our Service Area
We cover cap and crown work across Port Richmond and the surrounding neighborhoods, including chimney cap & crown work in Kensington, chimney cap & crown work in Fishtown, and the rowhouse blocks through Frankford, Hunting Park and Northern Liberties. The stock in this part of the city is similar: shared chimneys, older flue tiles, and crowns that have taken decades of river-valley weather. Dispatch runs 7am to 7pm, Sunday through Friday, and we’ll tell you honestly when a booking lands. If you want the wider picture on flue care, start with chimney sweep Port Richmond.
Serving Port Richmond, PA – Our Local Coverage Area
We serve Port Richmond and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Port Richmond
A chimney cap is the metal lid over the flue, and the crown is the concrete slab at the top of the chimney around it. The cap keeps rain, animals and downdraft out of the flue; the crown sheds water away from the brick below. Together they’re the first line of defense for the whole chimney, and they’re the two parts that fail first on an older Port Richmond chimney.
Most cap installs and replacements are done in a single visit, often in under two hours. Crown coating and crown repairs usually take the better part of a day, and a full crown rebuild can run a full day depending on the size of the chimney and the setup. We give you the expected window when we book, and we don’t leave a crown unfinished overnight once the old material is off. Call (833) 754-6815 for an exact quote; estimates are free.
Estimated ranges for Port Richmond are roughly $250 – $650 for a single-flue cap, $600 – $1,400 for a multi-flue or custom cap, $400 – $800 for crown coating, and $600 – $2,500 for crown repair through full rebuild. The final price is set per job by the written estimate after we’ve seen the top of the chimney. We don’t price from a phone description, because a crown that looks cracked from the ground can be either a coating job or a rebuild. Call (833) 754-6815 for an exact quote; estimates are free.
Yes. Gelco and Famco caps are both part of our regular work, and we install replacements in both brands as well as servicing existing ones. We know the failure points on each: the top plate and screen crimp on older Gelco units, the frame fixings on Famco caps on multi-flue chimneys. If you’re not sure what’s on your chimney, we’ll identify it during the inspection.
Same-day bookings are often possible, depending on the schedule on the day you call. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a call on Saturday is booked into the next opening. Call (833) 754-6815 to check availability.
Yes, our work carries a satisfaction guarantee, and the caps we install come with the manufacturer’s warranty on the product itself. What that covers depends on the brand and the cap, and we’ll tell you the terms in writing with the estimate rather than after the work is done. If something isn’t right with the install, we come back and put it right.
Clear access to the fireplace and the hearth, and move anything breakable away from the chimney breast, since crown work involves some vibration at the top. Tell us about any leaks you’ve noticed and when they show up, because that helps us trace the water. If you have the make of any existing cap, have it ready, but it’s not essential; we’ll identify it on site.
Schedule Your Chimney Cap & Crown Service in Port Richmond Today
A cap and crown job done now protects the flue, the damper and the brick below it for years. Call (833) 754-6815 for a free, no-obligation estimate on a chimney cap & crown in Port Richmond, and we’ll get a technician out to look at the top of your chimney and show you exactly what’s going on. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. One company for the sweep, the repair and the crown, from the firebox to the top.
Written by the team at Chimney Sweep Port Richmond.